This feature is not available on all camera models.
The Behavioral Detection is an extension to MxAnalytics. This feature can create alarms based on movements of the tracked objects. In order to configure alarms, it is not required to explicitly activate MxAnalytics. All required parameters can be accessed on the configuration page of the Image Analysis Events.
Note that you can create different image analysis events, which react to different behavior profiles.
This section shows the general settings that are used in the entire behavioral detection. Parameters used only for specific alarms are configured directly at the event sensor type.
Sets the main direction of movement as a position of the clock face (12 o'clock corresponds to the North direction in the image). This parameter defines the direction, into which the detected objects are supposed to be moving.
Activate this parameter to show icons in the image for triggered alarms.
In addition, you can show the speed for the detected objects. Note that the precision of the speed measurement is depending greatly on how precisely you specified the Mounting Height and the Tilt Angle.
The Behavioral Detection is based on the MxAnalytics algorithms. This is why both features are sharing the configuration parameters listed in this section. For more detailed information on the shared parameters, please open the MxAnalytics help page.
Use the parameters in this section to define the alarms. You can choose between different behavior profiles for this purpose.
Profile |
Parameter |
Description |
||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Corridor |
Corridor List:
|
Triggers an alarm if an object moves through the entire length of one of the defined corridors. |
||||||||||||||||||
Duration of Stay |
Maximum duration of stay:
|
Triggers an alarm if an object stays longer in the image than the specified maximum duration of stay. |
||||||||||||||||||
Opposite Direction |
Main Direction:
|
Triggers an alarm if an object moves opposite to the configured main direction. |
||||||||||||||||||
U-Turn |
(None) |
Triggers an alarm if an object changes its direction of movement by an angle from 135° to 180°. |
||||||||||||||||||
Turn |
(None) |
Triggers an alarm if an object changes its direction of movement by an angle from 45° to 134°. |
||||||||||||||||||
Speed |
Speed threshold:
|
Triggers an alarm if an object moves faster than the specified speed. |
||||||||||||||||||
Restricted Area |
Area Definition: The restricted area can be defined as a rectangle or as a polygon. Rectangle Syntax image sensor, horizontal position, vertical position, width, height Example 1. Rectangle Syntax
0,270,190,100,100 Polygon Syntax image sensor, poly=<hor. coordinate>x<vert. coordinate> {/<hor. coordinate>x<vert. coordinate>} Example 2. Polygon Syntax
0,poly=270x190/270x289/369x289/369x190 Notes
NoteIf you would like to define a new or additional window, open the Image Analysis Events dialog and follow the instructions of the Graphically Entering Image Areas help page. |
Triggers an alarm if an object enters the restricted area. NoteTo trigger the alarm, the camera uses the estimated position where the object touches the ground. in case of a person, this would be the estimated position of the person's feet. The Object trace is thus no suitable means to control this type of access since it follows the object's center of gravity. |
設定 ボタンをクリックすると、次にカメラが再起動するまでの間、設定内容が保存され有効になります。
出荷時設定 ボタンをクリックして、このダイアログに工場出荷時設定値をロードします (このボタンはすべてのダイアログにはありません)。
リストア ボタンをクリックすると、カメラに永久保存される前の直近の変更が元に戻ります。
閉じる ボタンをクリックするとダイアログが終了します。ダイアログを終了している間、システムは設定全体に変更があるかどうか確認をします。設定に変更が検出されると、システム設定値を永久に保存するかどうか確認されます。